pseudowire

This document expands the applicability of Virtual Private Wire Service (VPWS) bit-stream payloads beyond Time Division Multiplexing (TDM) signals and provides pseudowire transport with complete signal transparency over Packet Switched Networks (PSNs).

The pseudowire (PW) encapsulation of Ethernet, as defined in RFC 4448, specifies that the use of the control word (CW) is optional. In the absence of the CW, an Ethernet PW packet can be misidentified as an IP packet by a label switching router (LSR). This may lead to the selection of the wrong equal-cost multipath (ECMP) path for the packet, leading in turn to the misordering of packets. This problem has become more serious due to the deployment of equipment with Ethernet Media Access Control (MAC) addresses that start with 0x4 or 0x6. The use of the Ethernet PW CW addresses this problem. This document RECOMMENDS the use of the Ethernet PW CW in all but exceptional circumstances.

This document updates RFC 4448.

This document defines protocol extensions required to synchronize flow label states among Provider Edges (PEs) when using the BGP-based signaling procedures. These protocol extensions are equally applicable to point-to-point Layer 2 Virtual Private Networks (L2VPNs). This document updates RFC 4761 by defining new flags in the Control Flags field of the Layer2 Info Extended Community.

Label Switched Path (LSP) Ping is a widely deployed Operation, Administration, and Maintenance (OAM) mechanism in MPLS networks. This document describes a mechanism to verify connectivity of Point-to-Multipoint (P2MP) Pseudowires (PWs) using LSP Ping.

This document specifies a mechanism to signal Point-to-Multipoint (P2MP) Pseudowire (PW) trees using LDP. Such a mechanism is suitable for any Layer 2 VPN service requiring P2MP connectivity over an IP or MPLS-enabled PSN. A P2MP PW established via the proposed mechanism is root initiated. This document updates RFC 7385 by reassigning the reserved value 0xFF to be the wildcard transport tunnel type.

This document describes a method for generating an aggregated pseudowire (PW) status message transmitted for a statically configured PW on a Multiprotocol Label Switching (MPLS) Label Switched Path (LSP) to indicate the status of one or more PWs carried on the LSP.

The method for transmitting the PW status information is not new; however, this protocol extension allows a Service Provider (SP) to reliably monitor the individual PW status while not overwhelming the network with multiple periodic status messages. This is achieved by sending a single cumulative summary status verification message for all the PWs grouped in the same LSP.

This document describes the procedures and recommendations for Virtual Private LAN Service (VPLS) Provider Edges (PEs) to facilitate replication of multicast traffic to only certain ports (behind which there are interested Protocol Independent Multicast (PIM) routers and/or Internet Group Management Protocol (IGMP) hosts) via PIM snooping and proxying.

With PIM snooping, PEs passively listen to certain PIM control messages to build control and forwarding states while transparently flooding those messages. With PIM proxying, PEs do not flood PIM Join/Prune messages but only generate their own and send them out of certain ports, based on the control states built from downstream Join/Prune messages. PIM proxying is required when PIM Join suppression is enabled on the Customer Edge (CE) devices and is useful for reducing PIM control traffic in a VPLS domain.

This document also describes PIM relay, which can be viewed as lightweight proxying, where all downstream Join/Prune messages are simply forwarded out of certain ports and are not flooded, thereby avoiding the triggering of PIM Join suppression on CE devices.

This document describes a framework and several scenarios for a pseudowire (PW) dual-homing local protection mechanism that avoids unnecessary switchovers and does not depend on whether a control plane is used. A Dual-Node Interconnection (DNI) PW is used to carry traffic between the dual-homing Provider Edge (PE) nodes when a failure occurs in one of the Attachment Circuits (AC) or PWs. This PW dual-homing local protection mechanism is complementary to existing PW protection mechanisms.

In some scenarios, MPLS Transport Profile (MPLS-TP) pseudowires (PWs) (RFC 5921) may be statically configured when a dynamic control plane is not available. A fast protection mechanism for MPLS-TP PWs is needed to protect against the failure of an Attachment Circuit (AC), the failure of a Provider Edge (PE), or a failure in the Packet Switched Network (PSN). The framework and typical scenarios of dual- homing PW local protection are described in RFC 8184. This document proposes a dual-homing coordination mechanism for MPLS-TP PWs that is used for state exchange and switchover coordination between the dual- homing PEs for dual-homing PW local protection.

This document describes a tunnel encapsulation for Ethernet over IPv6 with a mandatory 64-bit cookie for connecting Layer 2 (L2) Ethernet attachment circuits identified by IPv6 addresses. The encapsulation is based on the Layer 2 Tunneling Protocol Version 3 (L2TPv3) over IP and does not use the L2TPv3 control plane.

This document specifies a fast mechanism for protecting pseudowires (PWs) transported by IP/MPLS tunnels against egress endpoint failures, including egress attachment circuit (AC) failure, egress provider edge (PE) failure, multi-segment PW terminating PE failure, and multi-segment PW switching PE failure. Operating on the basis of multihomed customer edge (CE), redundant PWs, upstream label assignment, and context-specific label switching, the mechanism enables local repair to be performed by the router upstream adjacent to a failure. The router can restore a PW in the order of tens of milliseconds, by rerouting traffic around the failure to a protector through a pre-established bypass tunnel. Therefore, the mechanism can be used to reduce traffic loss before global repair reacts to the failure and the network converges on the topology changes due to the failure.

Layer 2 services (such as Frame Relay, Asynchronous Transfer Mode, and Ethernet) can be emulated over an MPLS backbone by encapsulating the Layer 2 Protocol Data Units (PDUs) and then transmitting them over pseudowires (PWs). It is also possible to use pseudowires to provide low-rate Time-Division Multiplexed and Synchronous Optical NETworking circuit emulation over an MPLS-enabled network. This document specifies a protocol for establishing and maintaining the pseudowires, using extensions to the Label Distribution Protocol (LDP). Procedures for encapsulating Layer 2 PDUs are specified in other documents.

This document is a rewrite of RFC 4447 for publication as an Internet Standard.

Multiprotocol Label Switching (MPLS) is being extended to the edge of operator networks including the network access nodes. Separately, network access nodes such as Passive Optical Network (PON) Optical Line Terminations (OLTs) have evolved to support first-mile access protection, where one or more physical OLTs provide first-mile diversity to the customer edge. Multihoming support is needed on the MPLS-enabled PON OLT to provide resiliency for provided services. This document describes the Multi-Chassis PON (MC-PON) protection architecture in MPLS and also specifies the Inter-Chassis Communication Protocol (ICCP) extension to support it.

Multiprotocol Label Switching (MPLS) Label Switched Path (LSP) ping and traceroute are methods used to test Equal-Cost Multipath (ECMP) paths. Ping is known as a connectivity-verification method and traceroute is known as a fault-isolation method, as described in RFC 4379. When an LSP is signaled using the Entropy Label (EL) described in RFC 6790, the ability for LSP ping and traceroute operations to discover and exercise ECMP paths is lost for scenarios where Label Switching Routers (LSRs) apply different load-balancing techniques. One such scenario is when some LSRs apply EL-based load balancing while other LSRs apply load balancing that is not EL based (e.g., IP). Another scenario is when an EL-based LSP is stitched with another LSP that can be EL based or not EL based.

This document extends the MPLS LSP ping and traceroute multipath mechanisms in RFC 6424 to allow the ability of exercising LSPs that make use of the EL. This document updates RFC 6790.

Many transport services require that user traffic, in the form of Pseudowires (PWs), be delivered via either a single co-routed bidirectional tunnel or two unidirectional tunnels that share the same routes. This document defines an optional extension to the Label Distribution Protocol (LDP) that enables the binding between PWs and the underlying Traffic Engineering (TE) tunnels. The extension applies to both single-segment and multi-segment PWs.

This document defines Seamless BFD (S-BFD) for VCCV by extending the procedures and Connectivity Verification (CV) types already defined for Bidirectional Forwarding Detection (BFD) for Virtual Circuit Connectivity Verification (VCCV).

This document updates RFC 5885 by extending the CV Type values and the capability selection.

Pseudowires (PWs) have become a common mechanism for tunneling traffic and may be found in unmanaged scenarios competing for network resources both with other PWs and with non-PW traffic, such as TCP/IP flows. Thus, it is worthwhile specifying under what conditions such competition is acceptable, i.e., the PW traffic does not significantly harm other traffic or contribute more than it should to congestion. We conclude that PWs transporting responsive traffic behave as desired without the need for additional mechanisms. For inelastic PWs (such as Time Division Multiplexing (TDM) PWs), we derive a bound under which such PWs consume no more network capacity than a TCP flow. For TDM PWs, we find that the level of congestion at which the PW can no longer deliver acceptable TDM service is never significantly greater, and is typically much lower, than this bound. Therefore, as long as the PW is shut down when it can no longer deliver acceptable TDM service, it will never do significantly more harm than even a single TCP flow. If the TDM service does not automatically shut down, a mechanism to block persistently unacceptable TDM pseudowires is required.

This document specifies a generic Virtual Private LAN Service (VPLS) solution, which uses VLANs to indicate root or leaf traffic to support Ethernet-Tree (E-Tree) services. A VPLS Provider Edge (PE) model is illustrated as an example for the solution. In the solution, E-Tree VPLS PEs are interconnected by Pseudowires (PWs), which carry the VLAN indicating the E-Tree attribute. The MAC address-based Ethernet forwarding engine and the PW work in the same way as specified in RFC 4762 and RFC 4448, respectively. A signaling mechanism is described to support E-Tree capability and VLAN mapping negotiation.

This document describes Multi-Segment Pseudowire (MS-PW) protection scenarios in which pseudowire redundancy is provided on the Switching Provider Edge (S-PE) as defined in RFC 5659. Operations of the S-PEs that provide PW redundancy are specified in this document. Signaling of the Preferential Forwarding status as defined in RFCs 6870 and 6478 is reused. This document does not require any change to the Terminating Provider Edges (T-PEs) of MS-PW.

This document specifies a mechanism to signal Media Access Control (MAC) address withdrawal notification using a pseudowire (PW) Associated Channel (ACH). Such notification is useful when statically provisioned PWs are deployed in a Virtual Private LAN Service (VPLS) or Hierarchical Virtual Private LAN Service (H-VPLS) environment.

In MPLS and MPLS Transport Profile (MPLS-TP) environments, statically provisioned Single-Segment Pseudowires (SS-PWs) are protected against tunnel failure via MPLS-level and MPLS-TP-level tunnel protection. With statically provisioned Multi-Segment Pseudowires (MS-PWs), each segment of the MS-PW is likewise protected from tunnel failures via MPLS-level and MPLS-TP-level tunnel protection. However, static MS-PWs are not protected end-to-end against failure of one of the Switching Provider Edge Routers (S-PEs) along the path of the MS-PW. This document describes how to achieve this protection via redundant MS-PWs by updating the existing procedures in RFC 6870. It also contains an optional approach based on MPLS-TP Linear Protection.

The Inter-Chassis Communication Protocol (ICCP) supports an inter-chassis redundancy mechanism that is used to support high network availability.

In this document, Provider Edge (PE) devices in a Redundancy Group (RG) running ICCP are used to offer multihomed connectivity to Spanning Tree Protocol (STP) networks to improve availability of the STP networks. The ICCP TLVs and usage for the ICCP STP application are defined.

The Virtual Circuit Connectivity Verification (VCCV) protocol specified in RFC 5085 provides a control channel (CC) that is associated with a pseudowire (PW). This document specifies an additional VCCV control channel type to be used with pseudowires that do not use the PW Control Word and that are carried over an MPLS network. This new VCCV CC type uses the Generic Associated Channel Label defined in RFC 5586 to distinguish VCCV packets from packets carrying user data. This new VCCV CC type introduces compatibility with the method of MPLS Label Switched Path Operations, Administration, and Maintenance (OAM) identification, particularly in MPLS Transport Profile (MPLS-TP) networks (RFC 5921).

When set up through an explicit path, dynamic Multi-Segment Pseudowires (MS-PWs) may be required to provide a simple solution for 1:1 protection with diverse primary and backup MS-PWs for a service, or to enable controlled signaling (strict or loose) for special MS-PWs. This document specifies the extensions and procedures required to enable dynamic MS-PWs to be established along explicit paths.

This document presents a set of requirements and a framework for providing a point-to-multipoint pseudowire (PW) over MPLS Packet Switched Networks. The requirements identified in this document are related to architecture, signaling, and maintenance aspects of point-to-multipoint PW operation. They are proposed as guidelines for the standardization of such mechanisms. Among other potential applications, point-to-multipoint PWs can be used to optimize the support of multicast Layer 2 services (Virtual Private LAN Service and Virtual Private Multicast Service).

This document specifies an Inter-Chassis Communication Protocol (ICCP) that enables Provider Edge (PE) device redundancy for Virtual Private Wire Service (VPWS) and Virtual Private LAN Service (VPLS) applications. The protocol runs within a set of two or more PEs, forming a Redundancy Group, for the purpose of synchronizing data among the systems. It accommodates multi-chassis attachment circuit redundancy mechanisms as well as pseudowire redundancy mechanisms.

RFC 5254 describes the service provider requirements for extending the reach of pseudowires (PWs) across multiple Packet Switched Network domains. A multi-segment PW is defined as a set of two or more contiguous PW segments that behave and function as a single point-to-point PW. This document describes extensions to the PW control protocol to dynamically place the segments of the multi-segment pseudowire among a set of Provider Edge (PE) routers. This document also updates RFC 6073 by updating the value of the Length field of the PW Switching Point PE Sub-TLV Type 0x06 to 14.

This document specifies how to interconnect a pair of Transparent Interconnection of Lots of Links (TRILL) switch ports using pseudowires under existing TRILL and Pseudowire Emulation End-to-End (PWE3) standards.

This document specifies how signaling and selection processes for Pseudowire (PW) Virtual Circuit Connectivity Verification (VCCV) are modified to ensure backward compatibility and allow use of proactive Connectivity Verification (CV), Continuity Check (CC), and Remote Defect Indication (RDI) over MPLS Transport Profile (MPLS-TP) PWs. This document introduces four new CV types and, to accommodate them, a new VCCV Extended CV parameter for PW Interface Parameters Sub-TLV is defined.

The IETF Pseudowire Emulation Edge-to-Edge (PWE3) working group has defined many encapsulations of various layer 1 and layer 2 service- specific PDUs and circuit data. In most of these encapsulations, use of the Pseudowire (PW) Control Word is required. However, there are several encapsulations for which the Control Word is optional, and this optionality has been seen in practice to possibly introduce interoperability concerns between multiple implementations of those encapsulations. This survey of the Pseudowire / Virtual Circuit Connectivity Verification (VCCV) user community was conducted to determine implementation trends and the possibility of always mandating the Control Word.

This document specifies the mapping of defect states between Ethernet Attachment Circuits (ACs) and associated Ethernet pseudowires (PWs) connected in accordance with the Pseudowire Emulation Edge-to-Edge (PWE3) architecture to realize an end-to-end emulated Ethernet service. It standardizes the behavior of Provider Edges (PEs) with respect to Ethernet PW and AC defects.

The MPLS Generic Associated Channel (G-ACh) is a generalization of the applicability of the pseudowire (PW) Associated Channel Header (ACH). RFC 5586 defines the concept of TLV constructs that can be carried in messages on the G-ACh by placing them in the ACH between the fixed header fields and the G-ACh message. These TLVs are called ACH TLVs

No Associated Channel Type yet defined uses an ACH TLV. Furthermore, it is believed that handling TLVs in hardware introduces significant problems to the fast path, and since G-ACh messages are intended to be processed substantially in hardware, the use of ACH TLVs is undesirable.

This document updates RFC 5586 by retiring ACH TLVs and removing the associated registry.

This document describes a mechanism for signaling the active and standby status of redundant Pseudowires (PWs) between their termination points. A set of Redundant PWs is configured between Provider Edge (PE) nodes in single-segment pseudowire (SS-PW) applications or between Terminating Provider Edge (T-PE) nodes in Multi-Segment Pseudowire (MS-PW) applications.

In order for the PE/T-PE nodes to indicate the preferred PW to use for forwarding PW packets to one another, a new status bit is defined. This bit indicates a Preferential Forwarding status with a value of active or standby for each PW in a redundant set.

In addition, a second status bit is defined to allow peer PE nodes to coordinate a switchover operation of the PW.

Finally, this document updates RFC 4447 by adding details to the handling of the PW status code bits in the PW Status TLV.

This document describes a framework comprised of a number of scenarios and associated requirements for pseudowire (PW) redundancy. A set of redundant PWs is configured between provider edge (PE) nodes in single-segment PW applications or between terminating PE (T-PE) nodes in multi-segment PW applications. In order for the PE/T-PE nodes to indicate the preferred PW to use for forwarding PW packets to one another, a new PW status is required to indicate the preferential forwarding status of active or standby for each PW in the redundant set. This document is not an Internet Standards Track specification; it is published for informational purposes.

This document describes a pseudowire mechanism that is used to transport a packet service over an MPLS PSN in the case where the client Label Switching Router (LSR) and the server Provider Edge equipments are co-resident in the same equipment. This pseudowire mechanism may be used to carry all of the required layer 2 and layer 3 protocols between the pair of client LSRs. [STANDARDS-TRACK]

The "Typed Wildcard Forwarding Equivalence Class (FEC) Element" defines an extension to the Label Distribution Protocol (LDP) that can be used when requesting, withdrawing, or releasing all label bindings for a given FEC Element type is desired. However, a Typed Wildcard FEC Element must be individually defined for each FEC Element type. This specification defines the Typed Wildcard FEC Elements for the Pseudowire Identifier (PWid) (0x80) and Generalized PWid (0x81) FEC Element types. [STANDARDS-TRACK]

Layer 2 Virtual Private Networks (L2VPNs) based on Frame Relay or ATM circuits have been around a long time; more recently, Ethernet VPNs, including Virtual Private LAN Service, have become popular. Traditional L2VPNs often required a separate Service Provider infrastructure for each type and yet another for the Internet and IP VPNs. In addition, L2VPN provisioning was cumbersome. This document presents a new approach to the problem of offering L2VPN services where the L2VPN customer's experience is virtually identical to that offered by traditional L2VPNs, but such that a Service Provider can maintain a single network for L2VPNs, IP VPNs, and the Internet, as well as a common provisioning methodology for all services. This document is not an Internet Standards Track specification; it is published for informational purposes.

This document specifies a mechanism to signal Pseudowire (PW) status messages using a PW associated channel (ACh). Such a mechanism is suitable for use where no PW dynamic control plane exits, known as static PWs, or where a Terminating Provider Edge (T-PE) needs to send a PW status message directly to a far-end T-PE. The mechanism allows PW Operations, Administration, and Maintenance (OAM) message mapping and PW redundancy to operate on static PWs. This document also updates RFC 5885 in the case when Bi-directional Forwarding Detection (BFD) is used to convey PW status-signaling information. [STANDARDS-TRACK]

A Fibre Channel pseudowire (PW) is used to carry Fibre Channel traffic over an MPLS network. This enables service providers to take advantage of MPLS to offer "emulated" Fibre Channel services. This document specifies the encapsulation of Fibre Channel traffic within a pseudowire. It also specifies the common procedures for using a PW to provide a Fibre Channel service. [STANDARDS-TRACK]

This document describes the application of MPLS multi-segment pseudowires (MS-PWs) in a dual-technology environment comprising a Passive Optical Network (PON) and an MPLS Packet Switched Network (PSN).

PON technology may be used in mobile backhaul networks to support the end segments closest to the aggregation devices. In these cases, there may be a very large number of pseudowire (PW) Terminating Provider Edge (T-PE) nodes. The MPLS control plane could be used to provision these end segments, but support for the necessary protocols would complicate the management of the T-PEs and would significantly increase their expense. Alternatively, static, or management plane, configuration could be used to configure the end segments, but the very large number of such segments in a PON places a very heavy burden on the network manager.

This document describes how to set up the end segment of an end-to- end MPLS PW over a Gigabit-capable Passive Optical Network (G-PON) or 10 Gigabit-capable Passive Optical Network (XG-PON) using the G-PON and XG-PON management protocol, Optical Network Termination Management and Control Interface (OMCI). This simplifies and speeds up PW provisioning compared with manual configuration.

This document also shows how an MS-PW may be constructed from an end segment supported over a PON, and switched to one or more segments supported over an MPLS PSN. This document is not an Internet Standards Track specification; it is published for informational purposes.

Where the payload of a pseudowire comprises a number of distinct flows, it can be desirable to carry those flows over the Equal Cost Multiple Paths (ECMPs) that exist in the packet switched network. Most forwarding engines are able to generate a hash of the MPLS label stack and use this mechanism to balance MPLS flows over ECMPs.

This document describes a method of identifying the flows, or flow groups, within pseudowires such that Label Switching Routers can balance flows at a finer granularity than individual pseudowires. The mechanism uses an additional label in the MPLS label stack. [STANDARDS-TRACK]

This document describes the requirements for using the Generic Associated Channel Label (GAL) in pseudowires (PWs) in MPLS Transport Profile (MPLS-TP) networks, and provides an update to the description of GAL usage in RFC 5586 by removing the restriction that is imposed on using GAL for PWs, especially in MPLS-TP environments. [STANDARDS-TRACK]

This document specifies the mapping and notification of defect states between a pseudowire (PW) and the Attachment Circuits (ACs) of the end-to-end emulated service. It standardizes the behavior of Provider Edges (PEs) with respect to PW and AC defects. It addresses ATM, Frame Relay, Time Division Multiplexing (TDM), and Synchronous Optical Network / Synchronous Digital Hierarchy (SONET/SDH) PW services, carried over MPLS, MPLS/IP, and Layer 2 Tunneling Protocol version 3/IP (L2TPv3/IP) Packet Switched Networks (PSNs). [STANDARDS-TRACK]

This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for modeling Synchronous Optical Network/Synchronous Digital Hierarchy (SONET/SDH) circuits over a Packet Switch Network (PSN). [STANDARDS-TRACK]

This document describes how to connect pseudowires (PWs) between different Packet Switched Network (PSN) domains or between two or more distinct PW control plane domains, where a control plane domain uses a common control plane protocol or instance of that protocol for a given PW. The different PW control plane domains may belong to independent autonomous systems, or the PSN technology is heterogeneous, or a PW might need to be aggregated at a specific PSN point. The PW packet data units are simply switched from one PW to another without changing the PW payload. [STANDARDS-TRACK]

Ethernet pseudowires are widely deployed to support packet transport of Ethernet services. These services in-turn provide transport for a variety of client networks, e.g., IP and MPLS. This document uses procedures defined in the existing IETF specifications of Ethernet pseudowires carried over MPLS networks.

Many of the requirements for the services provided by the mechanisms explained in this document are also recognized by the MPLS transport profile (MPLS-TP) design effort formed jointly by the IETF and ITU-T. The solution described here does not address all of the MPLS-TP requirements, but it provides a viable form of packet transport service using tools that are already available.

This document also serves as an indication that existing MPLS techniques form an appropriate basis for the design of a fully- featured packet transport solution addressing all of the requirements of MPLS-TP. This document is not an Internet Standards Track specification; it is published for informational purposes.

This document describes Connectivity Verification (CV) Types using Bidirectional Forwarding Detection (BFD) with Virtual Circuit Connectivity Verification (VCCV). VCCV provides a control channel that is associated with a pseudowire (PW), as well as the corresponding operations and management functions such as connectivity verification to be used over that control channel. [STANDARDS-TRACK]

This document describes an architecture for extending pseudowire emulation across multiple packet switched network (PSN) segments. Scenarios are discussed where each segment of a given edge-to-edge emulated service spans a different provider's PSN, as are other scenarios where the emulated service originates and terminates on the same provider's PSN, but may pass through several PSN tunnel segments in that PSN. It presents an architectural framework for such multi-segment pseudowires, defines terminology, and specifies the various protocol elements and their functions. This memo provides information for the Internet community.

This document defines additional Layer 2 Tunneling Protocol Version 3 (L2TPv3) bit values to be used within the "Circuit Status" Attribute Value Pair (AVP) to communicate finer-grained error states for Attachment Circuits (ACs) and pseudowires (PWs). It also generalizes the Active bit and deprecates the use of the New bit in the Circuit Status AVP, updating RFC 3931, RFC 4349, RFC 4454, RFC 4591, and RFC 4719. [STANDARDS-TRACK]

This document defines extensions to the Layer Two Tunneling Protocol version 3 (L2TPv3) for support of structure-agnostic and structure-aware (Circuit Emulation Service over Packet Switched Network (CESoPSN) style) Time-Division Multiplexing (TDM) pseudowires. Support of structure-aware (Time-Division Multiplexing over IP (TDMoIP) style) pseudowires over L2TPv3 is left for further study. [STANDARDS-TRACK]

This memo defines a Standards Track portion of the Management Information Base for use with network management protocols in the Internet community. In particular, it describes managed objects for modeling of Pseudowire Edge-to-Edge services carried over a general Packet Switched Network. [STANDARDS-TRACK]

This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes a MIB module for PW operation over Multiprotocol Label Switching (MPLS) Label Switching Routers (LSRs). [STANDARDS-TRACK]

This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for modeling of Ethernet pseudowire (PW) services. [STANDARDS-TRACK]

This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for pseudowire encapsulation for structured or unstructured Time-Division Multiplexing (TDM) (T1, E1, T3, E3) circuits over a Packet Switched Network (PSN). [STANDARDS-TRACK]

This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for modeling ATM Pseudowire (PW) carrying ATM cells over Packet Switched Networks (PSNs). [STANDARDS-TRACK]

This memo defines a Management Information Base (MIB) module that contains textual conventions (TCs) to represent commonly used pseudowire (PW) management information. The intent is that these TCs will be imported and used in PW-related MIB modules that would otherwise define their own representations. [STANDARDS-TRACK]

This RFC archives the report of the IETF - ITU-T Joint Working Team (JWT) on the application of MPLS to transport networks. The JWT recommended of Option 1: The IETF and the ITU-T jointly agree to work together and bring transport requirements into the IETF and extend IETF MPLS forwarding, OAM (Operations, Administration, and Management), survivability, network management and control plane protocols to meet those requirements through the IETF Standards Process. This RFC is available in ASCII (which contains a summary of the slides) and in PDF (which contains the summary and a copy of the slides). This memo provides information for the Internet community.

This document describes the necessary requirements to allow a service provider to extend the reach of pseudowires across multiple domains. These domains can be autonomous systems under one provider administrative control, IGP areas in one autonomous system, different autonomous systems under the administrative control of two or more service providers, or administratively established pseudowire domains. This memo provides information for the Internet community.

This document defines extension to the Pseudowire Emulation Edge-to-Edge (PWE3) control protocol RFC 4447 and PWE3 IANA allocations RFC 4446 required for the setup of Time-Division Multiplexing (TDM) pseudowires in MPLS networks. [STANDARDS-TRACK]

This document describes Virtual Circuit Connectivity Verification (VCCV), which provides a control channel that is associated with a pseudowire (PW), as well as the corresponding operations and management functions (such as connectivity verification) to be used over that control channel. VCCV applies to all supported access circuit and transport types currently defined for PWs. [STANDARDS-TRACK]

This document describes a method for encapsulating structured (NxDS0) Time Division Multiplexed (TDM) signals as pseudowires over packet-switching networks (PSNs). In this regard, it complements similar work for structure-agnostic emulation of TDM bit-streams (see RFC 4553). This memo provides information for the Internet community.

Time Division Multiplexing over IP (TDMoIP) is a structure-aware method for transporting Time Division Multiplexed (TDM) signals using pseudowires (PWs). Being structure-aware, TDMoIP is able to ensure TDM structure integrity, and thus withstand network degradations better than structure-agnostic transport. Structure-aware methods can distinguish individual channels, enabling packet loss concealment and bandwidth conservation. Accessibility of TDM signaling facilitates mechanisms that exploit or manipulate signaling. This memo provides information for the Internet community.

The signaling protocols used to establish point-to-point pseudowires include type-length-value (TLV) fields that identify pseudowire endpoints called attachment individual identifiers (AIIs). This document defines AII structures in the form of new AII TLV fields that support AII aggregation for improved scalability and Virtual Private Network (VPN) auto-discovery. It is envisioned that this would be useful in large inter-domain virtual private wire service networks where pseudowires are established between selected local and remote provider edge (PE) nodes based on customer need. [STANDARDS-TRACK]

Pseudowire signaling requires that the Pseudowire Type (PW Type) be identical in both directions. For certain applications the configuration of the PW Type is most easily accomplished by configuring this information at just one PW endpoint. In any form of LDP-based signaling, each PW endpoint must initiate the creation of a unidirectional LSP. In order to allow the initiation of these two LSPs to remain independent, a means is needed for allowing the PW endpoint (lacking a priori knowledge of the PW Type) to initiate the creation of an LSP. This document defines a Wildcard PW Type to satisfy this need. [STANDARDS-TRACK]

This document provides encapsulation formats and semantics for emulating Synchronous Optical Network/Synchronous Digital Hierarchy (SONET/SDH) circuits and services over MPLS. [STANDARDS-TRACK]

The document describes a transparent cell transport service that makes use of the "N-to-one" cell relay mode for Pseudowire Emulation Edge-to-Edge (PWE3) Asynchronous Transfer-Mode (ATM) cell encapsulation. [STANDARDS-TRACK]

An Asynchronous Transfer Mode (ATM) Pseudowire (PW) is used to carry ATM cells over an MPLS network. This enables service providers to offer "emulated" ATM services over existing MPLS networks. This document specifies methods for the encapsulation of ATM cells within a pseudowire. It also specifies the procedures for using a PW to provide an ATM service. [STANDARDS-TRACK]

This document defines a mechanism for preserving Frame Check Sequence (FCS) through Ethernet, Frame Relay, High-Level Data Link Control (HDLC), and PPP pseudowires. [STANDARDS-TRACK]

A pseudowire (PW) can be used to carry Point to Point Protocol (PPP) or High-Level Data Link Control (HDLC) Protocol Data Units over a Multiprotocol Label Switching (MPLS) network without terminating the PPP/HDLC protocol. This enables service providers to offer "emulated" HDLC, or PPP link services over existing MPLS networks. This document specifies the encapsulation of PPP/HDLC Packet Data Units (PDUs) within a pseudowire. [STANDARDS-TRACK]

A frame relay pseudowire is a mechanism that exists between a provider's edge network nodes and that supports as faithfully as possible frame relay services over an MPLS packet switched network (PSN). This document describes the detailed encapsulation necessary to transport frame relay packets over an MPLS network. [STANDARDS-TRACK]

The Layer 2 Tunneling Protocol (L2TP) provides a standard method for setting up and managing L2TP sessions to tunnel a variety of L2 protocols. One of the reference models supported by L2TP describes the use of an L2TP session to connect two Layer 2 circuits attached to a pair of peering L2TP Access Concentrators (LACs), which is a basic form of Layer 2 Virtual Private Network (L2VPN). This document defines the protocol extensions for L2TP to set up different types of L2VPNs in a unified fashion. [STANDARDS-TRACK]

This document defines a generalized method of performing fragmentation for use by Pseudowire Emulation Edge-to-Edge (PWE3) protocols and services. [STANDARDS-TRACK]

This document describes a pseudowire encapsulation for Time Division Multiplexing (TDM) bit-streams (T1, E1, T3, E3) that disregards any structure that may be imposed on these streams, in particular the structure imposed by the standard TDM framing. [STANDARDS-TRACK]

This document allocates the fixed pseudowire identifier and other fixed protocol values for protocols that have been defined in the Pseudo Wire Edge to Edge (PWE3) working group. Detailed IANA allocation instructions are also included in this document. This document specifies an Internet Best Current Practices for the Internet Community, and requests discussion and suggestions for improvements.

An Ethernet pseudowire (PW) is used to carry Ethernet/802.3 Protocol Data Units (PDUs) over an MPLS network. This enables service providers to offer "emulated" Ethernet services over existing MPLS networks. This document specifies the encapsulation of Ethernet/802.3 PDUs within a pseudowire. It also specifies the procedures for using a PW to provide a "point-to-point Ethernet" service. [STANDARDS-TRACK]

The Layer 2 Tunneling Protocol, Version 3, (L2TPv3) defines a protocol for tunneling a variety of data link protocols over IP networks. This document describes the specifics of how to tunnel High-Level Data Link Control (HDLC) frames over L2TPv3. [STANDARDS-TRACK]

This document describes the preferred design of a Pseudowire Emulation Edge-to-Edge (PWE3) Control Word to be used over an MPLS packet switched network, and the Pseudowire Associated Channel Header. The design of these fields is chosen so that an MPLS Label Switching Router performing MPLS payload inspection will not confuse a PWE3 payload with an IP payload. [STANDARDS-TRACK]

This document defines the specific requirements for edge-to-edge emulation of circuits carrying Time Division Multiplexed (TDM) digital signals of the Plesiochronous Digital Hierarchy as well as the Synchronous Optical NETwork/Synchronous Digital Hierarchy over packet-switched networks. It is aligned to the common architecture for Pseudo Wire Emulation Edge-to-Edge (PWE3). It makes references to the generic requirements for PWE3 where applicable and complements them by defining requirements originating from specifics of TDM circuits. This memo provides information for the Internet community.

This document describes an architecture for Pseudo Wire Emulation Edge-to-Edge (PWE3). It discusses the emulation of services such as Frame Relay, ATM, Ethernet, TDM, and SONET/SDH over packet switched networks (PSNs) using IP or MPLS. It presents the architectural framework for pseudo wires (PWs), defines terminology, and specifies the various protocol elements and their functions. This memo provides information for the Internet community.

This document describes base requirements for the Pseudo-Wire Emulation Edge to Edge Working Group (PWE3 WG). It provides guidelines for other working group documents that will define mechanisms for providing pseudo-wire emulation of Ethernet, ATM, and Frame Relay. Requirements for pseudo-wire emulation of TDM (i.e., "synchronous bit streams at rates defined by ITU G.702") are defined in another document. It should be noted that the PWE3 WG standardizes mechanisms that can be used to provide PWE3 services, but not the services themselves. This memo provides information for the Internet community.